Tools

Park's Chainring Nut Wrench makes chainring bolt installation and removal easy. It securely holds the slotted nut to prevent spinning when tightening or loosening the bolt. And, it's double-ended to fit most slotted-type nuts, including Campagnolo chainring bolt nuts.

Park's Compact Crank Puller is used to remove Shimano Octalink, ISIS Drive and square-taper cranksets. It includes 2 rotating tips (16.3 and 11.3mm) to make the job easy. This is a great tool for your travel and home tool kit.

Park's Crank Puller is for removing crankarms on Shimano's splined, oversize, pipe-billet bottom brackets. It employs a long handle and a fine thread for the leverage and torque needed to remove tight arms. Park's unique rotating tip ensures smooth operation and long life. (The CCP-44 does not fit standard square or tapered bottom brackets.)

A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.

The 2197 is an add-on accessory for the Park Tool DT-5 and DT-5.2 Disc Brake Mount Facing Set to enable easier and more efficient facing of disc brake mounts on carbon fiber frames. Features a brazed-on diamond grit surface that is over 100 times more durable and effective on carbon fiber than the cutter included with the DT-5.2. The 2197 sits between the cutter of the DT-5.2 and the brake mount, and smoothly and evenly grinds the mounting surface until it is flat and properly perpendicular to the rotor. NOTE: The 2197 is intended for facing carbon fiber only. Aluminum, steel, and titanium disc brake mounts should be faced using the #2171 facing cutter included with the DT-5.2. For carbon frames that feature aluminum inserts (with a carbon/aluminum hybrid mounting surface), use the #2197. When machining carbon fiber, regularly apply water (or a similar solution) to the cutting surface.

The Park FR-2 Freewheel Remover fits SunTour two-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel. (Not recommended for use with SunTour 4- and 6-notch freewheels.)

The Park FR-4 Freewheel Remover fits Atom, Regina, splined Zeus and some Schwinn-approved freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.

The Park FR-6 Freewheel Remover fits most 4-notch BMX and singlespeed freewheels. It can be held with a wrench or vise and its narrow profile allows use without removal of cones and locknuts.

The Park FR-7 Freewheel Remover fits Falcon freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.

The Park Tool FWS-2 Fold-Up Wrench Set combines all the popular hex and Torx compatible wrench sizes of the AWS-10 and TWS-2 into one convenient set. The multi-position shop grade fold-ups are comfortable, lightweight, slip-resistant, and 40% stronger than steel handles. Made in USA.

Park's Hex Wrench Set offers all the popular Allen wrenches (1.5, 2, 2.5, 3, 4, 5 and 6mm) in a convenient fold-up unit. The tool tips are chamfered for a positive grip and the one-piece fiber-reinforced-resin handle is light, comfortable, slip resistant and 40% stronger than steel.

Park's Hex Wrench Set offers 3, 4, 5, 6, 8, and 10mm Allen wrenches with chamfered tips for a great grip and easy use. The one-piece fiber-reinforced-resin handle is light, comfortable, slip-resistant, and 40% stronger than traditional steel handles.

12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.

Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.

Park's AWS-7 features a Y-shaped nylon handle with 4 and 5mm Allen wrenches and a T25 Torx wrench. This convenient 3-in-1 tool keeps commonly used wrenches together and offers an excellent grip as well.

Park's Home Mechanic Pedal Wrench is great for your home workshop and event tool box. This top-quality 15mm pedal wrench provides the leverage you need to remove stubborn pedals. It's made to last from heat-treated steel, and the handle has a vinyl grip for comfort.

Park's Hydraulic Brake Piston Press is used to set or reset the piston(s) inside hydraulic disc brake calipers during installation, maintenance and repair. Just push it into the caliper to wedge the piston into place. It's made of tough tool steel with a comfortable and oversize rubber handle for a great grip.

"Take the guesswork out of internal routing. The IR-1.3 speeds the installation of internally-routed cable, housing, electronic wiring and hydraulic hose into carbon fiber, titanium, and aluminum frames. The straightforward guide magnet system utilizes five long guide cables with unique fittings, which can be routed through the frame in a number of ways using the included guide magnet. Everything is neatly stored in a convenient compact case. A true time and frustration saver!??Includes five 188 cm (74"") guide cables with attached magnets and unique fittings: • Barbed adapter — Threads into the end of brake & shift cable housing as well as hydraulic brake hose • Rubber adapter — Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS • Di2®-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® shift wire, and is perfectly sized to fit into frame holes as small as 6 mm • Di2® EW-SD300-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® EW-SD300 shift wire • Reverse-polarity magnet — Used in conjunction with any of the other guide cables - feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes Also included: • Double-threaded barb — Securely attaches new housing or hydraulic hose to existing housing or hose, allowing for easy replacement without redoing the routing • Guide magnet — routes guide cables through the frame from the outside"

Precisely machined for a perfect fit, this 8-notch tool removes and installs the lockring that retains front chainrings found on Bosch Gen 2 e-bike motors after the crank arm is removed. - Fits Bosch Active Line (chainrings less than 20 teeth), Performance Line and Performance Line CX models - For lockrings with 50mm outside diameter and 8 notches - Replacement for Bosch 0275009003 tool - Torque wrench compatible 3/8-inch square drive - Constructed of 4140 heat treated steel and plated for long life

A purpose-built wrench designed for compression nuts, nipples, and other fittings found on hydraulic brake systems. The five-sided flare wrench head evenly spreads out the force being applied to the wrench, reducing the risk of damage to fasteners and brake hoses. Features a slim, low-profile design to access low-clearance fittings found on hydraulic levers and calipers. Built-in 3/8" fittings allow for use with a torque wrench to achieve proper torque. - Double-sided wrench features 7mm and 8mm wrench openings - Dimensions: 4" x 0.75" x 0.15" (101mm x 19.5mm x 4.5mm) - Weight: 44g (1.55 oz.) NOTE: When using with a torque wrench, the MWF-3 should be installed at a 90° angle from the beam of the wrench.

Many chains use a master link that allows the chain to be installed and removed by hand. While master links don't require traditional chain tools, over time, dirt and corrosion can make it difficult to separate them by hand. Park's Master Link Pliers make removing and installing these master links quick and easy. Simply insert the specially sized jaws into the link and squeeze the vinyl-coated handles!

Park’s Professional Cable And Housing Cutter is specifically for use on derailleur and brake cables and housing. It even makes quick work of hard-to-cut shift-cable housing. Its cold-forged, heat-treated-steel handles won't bend and its precision-ground jaws cut perfectly every time. Its dual-density molded grips are specially contoured for superior comfort and control. Plus, there’s a built-in cable-end crimper and a forming hole for reforming housing ends.

These shop-quality L-shaped hex wrenches have a genuine Bondhus balldriver tip on the long arm (excluding the 10mm) for hard-to-reach bolt heads and a straight tip on the short arm for high-torque applications. The HXS-1.2 includes a handy portable tool organizer/holder and it's hinged for easy access. • Includes 1.5, 2, 2.5, 3, 4, 5, 6, 8, and 10 mm sizes • Wrench tips are precision chamfered for a clean, tight fit • Made from industrial-quality Bondhus Protanium high torque steel

With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The Park Tool TW-5.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). With a range of 2-14Nm, the TW-5.2 is designed for the lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.

Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs

Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing. To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap. Works with the CT-4.3, CT-4.2, CT-4, and CT-11

Bicycle disc brake rotors can become warped from extensive use, excessive heat, or impact. Even new disc rotors may not always be perfectly straight, causing annoying pad rub and affecting performance. The Park Tool DT-2.2 is specially designed and precisely manufactured to gently adjust bent bicycle disc brake rotors. The DT-2.2 features one long slot and two short slots for maximum compatibility with any rotor design or thickness up to 2.5 mm. Constructed from high quality steel with a vinyl dipped handle for comfort. Compatible with rotors up to 2.5 mm thick

A perfect way to start a bicycle tool collection! A great combination of tools to help a home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-4 includes more than 15 genuine Park Tool products that can perform dozens of tasks and includes a custom Park Tool toolbox with extra room for spare parts and more tools. The SK-4 includes: - AWS-10 Fold-Up Hex Wrench Set - BBB-4 Big Blue Book of Bicycle Repair - CC-3.2 Chain Checker - CN-10 Professional Cable and Housing Cutter - CT-5 Mini ChainBrute Chain Tool - FR-5.2 Cassette Lockring Tool - GSC-1 GearClean Brush - HCW-16.3 Chain Whip/Pedal Wrench - HR-8 8mm Hex Wrench - MLP-1.2 Master Link Pliers - SD-2 Shop Screwdriver: #2 Phillips - SW-7.2 Triple Spoke Wrench - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench

Park's Pin Spanners are designed for maximum usefulness and versatility at the best value. Tough high-carbon tool steel is used to ensure long life and the handles are vinyl coated for a great grip and color-coded for easy identification. The red-handled SPA-2 is for turning the bearing cones on most freewheels and the one-key-release rings on crankarms.

Updated to fit current 12-speed cassettes, this combination chain whip and freewheel / lockring remover wrench is heat treated to prevent bending, flexing and wear and features a long, molded handle in addition to a built in hex shaped driver. - Works on 5- to 12-speed road and mountain bike cassettes and freewheels - 1-inch (25.4mm) box-end wrench fits Park Tool Freewheel / Cassette Lockring Tools - Features hardened pins to keep the chain in place